P0301 — Cylinder 1 misfire detected
A P0301 is the most useful misfire code you can get: it names a cylinder. Most of the ones that reach us are ignition, and most of those are the coil rather than the plug.
What the code actually means
The ECU watches how much the crankshaft speeds up after cylinder 1 fires and compares it with the other cylinders. When cylinder 1 contributes less, it stores P0301. It is set on the second consecutive drive cycle that shows the fault, which is why a P0301 that disappears for a week and comes back is usually a part breaking down with heat, not a broken wire.
Cylinder 1 is not always the one at the front of the engine. On most transverse fours it is at the timing-belt end, but some manufacturers number from the gearbox end. Confirm the numbering before you order, especially on French and Korean engines.
What you will notice
- A shake at idle that mostly disappears above 2,000 rpm — the signature of a coil breaking down when hot
- The engine light on steady, flashing under hard acceleration
- Roughness that starts 10–20 minutes after a cold start and gets worse in damp weather
- Fuel smell at the tailpipe, consumption up noticeably
- P0301 appearing together with P0171 — that combination usually means a lean cylinder, not a weak spark
Our order of checks
| Cause | Our category | Why it is on the list |
|---|---|---|
| Spark plug worn, fouled or wrong heat range | Spark plugs | Cheapest part and the fastest check. A cracked insulator misfires exactly like a dead coil. |
| Coil for cylinder 1 | Ignition coils | The single most common cause on coil-on-plug engines past 100,000 km. |
| Plug wire or boot, on wasted-spark engines | Spark plug wire sets | A chafed wire usually kills two cylinders; a cracked boot kills one. |
| Injector leaking or clogged | Fuel injectors | A lean cylinder misfires. If fuel trim on that bank is high, suspect the injector. |
| Intake gasket leak at that runner | — | Leans out one cylinder only, and gets worse when the engine is cold. |
Test before you buy
- Swap the coil with cylinder 2 and clear the code. If the misfire moves to P0302, the coil is dead. This one test settles most cases and costs nothing.
- If the code stays on cylinder 1, pull the plug and read it: black and wet means fuel or weak spark, white with a blistered electrode means lean or over-advanced.
- Compare coil primary resistance with a coil on a cylinder you know is good — never with a book value, because the value differs between coil families.
- Look for a thin grey carbon track down the inside of the boot, and for oil in the plug well. Both cause a misfire that a new coil will not fix until the oil leak is dealt with.
The expensive mistake
Replacing all four coils "while the cover is off" on a car with 60,000 km. The plug is usually the cause and the coil is the victim: a worn plug needs a higher firing voltage, and the coil takes the strain. Change the plug with the coil, or you will sell that coil again within a year.
Parts we stock for a P0301
Stocked numbers and fitment for these categories are in the catalogue; message us with the car details and we will pick the right one.
| Our category | Part numbers | When |
|---|---|---|
| Ignition Coils | 544 | Cylinder 1 coil — the usual fix |
| Spark Plugs | 141 | Change it with the coil, do not skip |
| Spark Plug Wire Sets | 182 | On wasted-spark engines only |
| Fuel Injectors | 168 | When the cylinder runs lean |
Questions we get
Is P0301 the coil or the plug?
Can I drive with a P0301?
Contact
广州驭盟扬汽配 · Guangzhou Yumengyang Auto Parts Co., Ltd.
E05, Yiyou (Guangyuan East) Auto Parts City, Baiyun District, Guangzhou, China
Send us the code, the car and the year. If this page points at several parts, we will tell you which one to change first — and which one not to change.