YumengyangAuto Parts
WhatsApp Us

P0335 — Crankshaft position sensor A circuit malfunction

OBD-II fault code · Crank, cam & timing · updated 2026-11-10 · English version is the reference

P0335 is one of the few codes that stops a car from starting at all. Without a crankshaft signal the ECU does not know where the engine is, so it will not fire the coils or the injectors.

What the code actually means

The crankshaft position sensor reports the position and speed of the crank. The ECU needs it to time both spark and injection, so when the signal is missing, intermittent or out of range, the engine stops. P0335 is stored when no usable signal is seen during cranking.

Two sensor types share this code: inductive (two wires, generates its own AC voltage) and Hall effect (three wires, needs a supply). The test procedure is different, and so is the part. Never order from the code alone.

What you will notice

  • Cranking with no start, often with the tachometer dead while cranking
  • An engine that starts, runs, then dies within seconds
  • A stall at speed followed by a no-start until it cools down — classic heat failure
  • Occasional backfire during cranking
  • Sometimes P0335 with no driveability problem at all on engines with a redundant sensor

Our order of checks

CauseOur categoryWhy it is on the list
Failing crankshaft position sensorCrankshaft position sensorsThe most common cause, and the sensor that fails with heat more than any other.
Damaged tone ring or reluctor—A cracked or rusty ring gives a signal the ECU cannot trust. No sensor fixes it.
Air gap wrong after a repair—A sensor fitted with a shim missing sits too far and reads nothing.
Loom damage near the sensor—The sensor wire runs close to the crank pulley and to hot parts.
Worn crank thrust or a broken keyway—Rare, but it moves the ring and the signal goes out of range.

Test before you buy

  1. Crank the engine and watch live cranking rpm on the scanner. Zero rpm means no signal at all — confirm the sensor or the loom.
  2. Identify the sensor type first. Two wires means inductive: measure resistance and compare with the spec for that engine, then check for AC volts while cranking. Three wires means Hall: check the supply voltage with the key on.
  3. Inspect the tone ring for cracks, missing teeth and rust, and check the air gap.
  4. Check continuity from the sensor connector to the ECU before condemning the sensor.

The expensive mistake

Selling a sensor for a car whose tone ring is cracked. The new sensor reads the same broken pattern and the car still does not start, and the part is now "no good" in the customer's eyes. Ask for a photo of the reluctor before shipping — it is a five-minute check that saves a return and a relationship.

Parts we stock for a P0335

Stocked numbers and fitment for these categories are in the catalogue; message us with the car details and we will pick the right one.

Our categoryPart numbersWhen
Crankshaft Position Sensors236Crankshaft position sensor — match the type
Camshaft Position Sensors159Check for a related cam code too

Questions we get

Will a bad crankshaft sensor always stop the engine?
Usually yes, because the ECU cannot time spark or injection without it. Some engines use a second sensor to limp home, which is why you sometimes see the code with the car still running.
Can I drive with a P0335?
Not reliably. It is a stall-and-no-start code. If the car still runs, it is intermittent and it will fail completely, often at the worst moment.

Contact

广州驭盟扬汽配 · Guangzhou Yumengyang Auto Parts Co., Ltd.

E05, Yiyou (Guangyuan East) Auto Parts City, Baiyun District, Guangzhou, China

Send us the code, the car and the year. If this page points at several parts, we will tell you which one to change first — and which one not to change.

WhatsApp +86 159 1585 9048 OE / cross-reference lookup